0xWheatyz
24d76b1fff
Insets uniformly 3.00 mm from each board edge. Hole pattern is 75.00 mm (X) x 54.00 mm (Y) center-to-centre on the 81 x 60 mm board. Hole specs per location: MH1 (63, 43) - top-left MH2 (138, 43) - top-right MH3 (63, 97) - bottom-left MH4 (138, 97) - bottom-right drill 2.2 mm (M2 medium-fit clearance), copper keep-out 4.0 mm dia, NPTH, no solder-mask opening. Constraint: M2 clearance hole, NPTH (no electrical connection) Constraint: board outline gr_rect (60,40)-(141,100) -> 81 x 60 mm Rejected: 2.5 mm inset | pad edge sits exactly on board edge clearance min Rejected: solder-mask opening on the pad | ESP32 silk at y=96.36 near MH3 produced two silk_over_copper warnings; bare drill (no mask opening) keeps DRC clean at the cost of less-visible holes Rejected: putting holes outside Edge.Cuts as silkscreen markers | user asked for real mounting holes, not indicators Confidence: high Scope-risk: narrow Directive: hole positions are coupled to the board outline -- if the outline changes, the 3.00 mm uniform inset must be recomputed
39 lines
1.6 KiB
Plaintext
39 lines
1.6 KiB
Plaintext
** Drc report for firstpcb.kicad_pcb **
|
|
** Created on 2026-05-15T16:12:52 **
|
|
** Report includes: Errors, Warnings, Exclusions **
|
|
|
|
** Found 6 DRC violations **
|
|
[lib_footprint_mismatch]: Footprint 'MountingHole_2.2mm_M2' does not match copy in library 'MountingHole'
|
|
Local override; warning
|
|
@(138.0000 mm, 97.0000 mm): Footprint MH4
|
|
[lib_footprint_mismatch]: Footprint 'MountingHole_2.2mm_M2' does not match copy in library 'MountingHole'
|
|
Local override; warning
|
|
@(138.0000 mm, 43.0000 mm): Footprint MH2
|
|
[lib_footprint_issues]: The current configuration does not include the footprint library 'Library'
|
|
Local override; warning
|
|
@(65.0000 mm, 53.3600 mm): Footprint ESP32-WROOM1
|
|
[lib_footprint_mismatch]: Footprint 'RHL0020A' does not match copy in library 'Project'
|
|
Local override; warning
|
|
@(118.2250 mm, 77.4750 mm): Footprint U2
|
|
[lib_footprint_mismatch]: Footprint 'MountingHole_2.2mm_M2' does not match copy in library 'MountingHole'
|
|
Local override; warning
|
|
@(63.0000 mm, 43.0000 mm): Footprint MH1
|
|
[lib_footprint_mismatch]: Footprint 'MountingHole_2.2mm_M2' does not match copy in library 'MountingHole'
|
|
Local override; warning
|
|
@(63.0000 mm, 97.0000 mm): Footprint MH3
|
|
|
|
** Found 0 unconnected pads **
|
|
|
|
** Found 0 Footprint errors **
|
|
|
|
** Ignored checks **
|
|
- Footprint has no courtyard defined
|
|
- Track endpoint not centered on via
|
|
- Tuning profile track geometries
|
|
- Footprint doesn't match symbol's footprint filters
|
|
- PTH inside courtyard
|
|
- NPTH inside courtyard
|
|
- Footprint component type doesn't match footprint pads
|
|
|
|
** End of Report **
|